#1 in Texason FloorRank ↗
Sugar Land, Texas · ESD Flooring
ESD Flooring in Sugar LandStatic control for electronics, labs and manufacturing
Sugar Land is mostly offices, clinics and light technology space off US 59 and Highway 6. New Era builds a conductive or dissipative floor into the room that needs one, tests it, and leaves the rest of the building alone.
- Free on-site estimates
- Since 2015 Houston grown
- Decade build standard
- Espanol Hablamos
Specifications
The numbers a plant engineer asks for
New Era installs the conductive grade. Here is the resistance band it is published at, how that compares with the dissipative grade, and the rest of the cured properties, so you can check the floor against your own ESD program before anybody quotes it.
Conductive
2.5 x 10^4 to 10^6 ohms
Charge drains fastest in this band. Tested to ASTM D257 and ANSI/ESD S7.1.
Dissipative
10^6 to 1.0 x 10^9 ohms
The band most electronics assembly programs specify. Available if yours calls for it.
| Property | Test method | Value |
|---|---|---|
| Resistance, conductive grade | ASTM D257, ANSI/ESD S7.1 | 2.5 x 10^4 to 10^6 ohms |
| Body voltage generation | ANSI/ESD STM 97.2 | 15 V |
| Compressive strength | ASTM D695 | 13,700 psi |
| Flexural strength | ASTM D790 | 9,000 psi |
| Tensile strength | ASTM D638 | 7,800 psi |
| Hardness | ASTM D2240 | 85 Shore D |
| Impact resistance | ASTM D2794 | 120 in-lbs |
| Abrasion resistance | ASTM D4060 | 15 to 20 mg |
| Adhesion over concrete | ASTM D4541 | 400 psi, concrete failure |
| Flame spread, critical flux | ASTM E648 | Class 1 |
| Rate of burning | ASTM D635 | Self-extinguishing |
| Microbial resistance | ASTM G21 | Passes, 0 growth |
| Indoor air quality | CA 01350 | Compliant |
| Moisture vapor permeance | ASTM E96 | 0.08 perms |
| Water absorption | ASTM D570 | Under 0.05 percent |
| Solids content | As supplied | 100 percent |
| Return to foot traffic | At 70F, 50 percent RH | 24 hours |
| Full cure, vehicle traffic | At 70F, 50 percent RH | 7 days |
| Applied thickness | 5 to 7 mil blade | 6 mils typical |
Values are the manufacturer published figures for the conductive system New Era installs. ANSI/ESD S20.20 caps a qualifying floor at under 1 x 10^9 ohms to ground and requires the finished floor to be tested in place, so treat these as the system specification and not as a substitute for your own acceptance test. Call (832) 253-3211 and we will spec it against your program. New Era's dedicated static control site has the standard broken down in plain terms, plus static control flooring in Sugar Land.
What esd flooring is, and why it works in Sugar Land
The typical Sugar Land job is a room inside a building that was not designed for static control: an IT room in a medical office, a device repair bench, a lab suite on the second floor of a business park. Those floors are often thin slabs or toppings over structure, which changes how we prep and how we read moisture, and it is the reason we visit before we write a number.
ESD Flooring across Sugar Land
Sugar Land is in Fort Bend County, along US 59, Highway 6 and the Grand Parkway, near Sugar Land Regional Airport. We serve these Sugar Land areas:
Where static control flooring goes in
In Sugar Land the static control room is often part of an interior renovation. Here is where static control floors show up in that kind of building.
IT rooms and network closets
Core rooms where switches and storage are serviced by technicians moving carts across the floor.
Medical device and clinic back rooms
Sterile processing, device repair and equipment staging inside clinics and outpatient buildings.
Small technology offices
Test benches and demo rooms that need a measured ground path without a full factory buildout.
How a static control floor actually goes down
Five stages. The last one is the one most contractors skip, and it is the only one that proves the floor does what the spec says.
Diamond grind the slab
Mechanical prep to clean, profiled concrete. No acid etch, no bonding to a surface that was never opened up.
Repair and level
Cracks, joints and spalls cut out and filled, moisture tested first and primed if the slab is pushing.
Lay the ground path
The conductive layer and its grounding connections, which is the part that makes it a static control floor instead of a coloured one.
Build the system
Base, conductive media and topcoat to the thickness your spec calls for, phased area by area so the line keeps running.
Test it and hand over readings
Point to point and point to ground measured on the finished floor, in writing. A floor nobody measured is a floor nobody can certify.
Why Sugar Land chooses New Era for ESD Flooring
Interior jobs live or die on prep and cleanup, so we contain dust and protect everything around the work.
- Full diamond-grind surface prep on every Sugar Land job, the real reason esd flooring lasts a decade.
- Commercial-grade ESD static control flooring with the right primer, build and topcoat for your space.
- Free on-site estimate before anything starts, with the number and the plan in writing.
- Fast-cure options and night or weekend scheduling so your Sugar Land home or business keeps moving.
- Established 2015, Houston grown, English and Spanish service end to end.
ESD Flooring in Sugar Land FAQ
Straight answers for Sugar Land offices, clinics and tech tenants, each ending with a way to get a quote.
Where a floor has to land
Static control flooring is bought and sold on one number, resistance to ground in ohms. This is that scale. New Era installs in the conductive band, and ANSI/ESD S20.20 will not qualify a floor to the right of the ceiling marked here.
New Era installs in the conductive band, 2.5 x 10^4 to 10^6 ohms.
What kind of facilities need ESD flooring in Sugar Land?
Facilities that have an ESD program on paper and a floor that does not support it. An audit finding usually points here. Sugar Land electronics and device makers, data hall operators and labs hear the same question at audit time: where does the charge go? Call (832) 253-3211 and we will answer it for your room.
Is ESD static control flooring chemical and stain resistant?
It resists most of what a Sugar Land plant or lab spills. Solvents are the exception, and we list them honestly: acetone, MEK, methanol, ethanol and 37 percent battery acid. Cleaning chemicals matter just as much for a static floor, because a film from the wrong cleaner changes the resistance. Call (832) 253-3211.
Hablan Espanol en Sugar Land?
Si. Cotizamos y trabajamos en ingles o espanol en Sugar Land. Llame al (832) 592-3808, o al (832) 253-3211 para una cotizacion gratis.
Do you offer free estimates in Sugar Land?
Always, and it includes the two slab tests that decide the whole system: moisture vapor emission (ASTM F1869) and internal relative humidity (ASTM F2170), plus an assessment of whatever is already down. We measure, talk through the options and put the pricing in writing at no cost. Call (832) 253-3211 and we typically respond within 24 hours.
Can you add anti-slip or safety features to ESD static control flooring?
Yes. We blend anti-slip aggregate into the system at 32 oz per kit and add striping and zone markings in the colors your Sugar Land safety plan uses. Aggregate is tuned so carts still roll and the floor still cleans. Call (832) 253-3211.
Can you handle large Sugar Land jobs and multi-phase work?
Size is a scheduling question for us. We agree an order with you, usually around shifts and deliveries, and we finish and test one area before we start the next. That is how a Sugar Land plant stays open during a large install. Call (832) 253-3211.
What system do you use for ESD static control flooring?
We lay a grounded system, not a single coat. Prep and base come first, then a conductive layer tied to ground, then the topcoat at 5 to 7 mils. Decorative flake and metallic finishes do not belong on a static control system, and we will not offer them as one. Call (832) 253-3211.
What Sugar Land areas do you serve?
Fourteen service areas across the Houston, Austin and San Antonio metros, Sugar Land included, plus the surrounding Texas markets. Call (832) 253-3211 and we will confirm we cover your address and book a free estimate.
Why choose New Era for ESD static control flooring in Sugar Land?
Because we give you numbers: the resistance band the system is published at, the standard it is measured to, and the readings from your own finished floor. One crew does the grind, the ground path and the topcoat in Sugar Land. Call (832) 253-3211 for a free quote.
What is the process for ESD static control flooring in Sugar Land?
Test, grind, repair, prime, build, topcoat. The slab gets tested first (ASTM F1869 and ASTM F2170), then we diamond-grind to clean profiled concrete, repair cracks and joints, prime where the slab needs it, then lay the conductive topcoat at 5 to 7 mils. Foot traffic at 24 hours, full cure at 7 days. You get the Sugar Land schedule up front. Call (832) 253-3211.
Can I see examples of ESD static control flooring you have done near Sugar Land?
Yes. We will share recent Sugar Land-area photos and references so you can see the finish before you commit. Call (832) 253-3211.
How do I prepare my Sugar Land space for ESD static control flooring?
Mostly access and temperature. Remove what you can, cover or move equipment that cannot go, and make sure we can run power and bring material in. Humidity under 90 percent and 5F above dew point are our application limits. Call (832) 253-3211 for a Sugar Land checklist.
What makes a floor fail, and how do you prevent it in Sugar Land?
In Sugar Land, the usual causes are a slab that was never tested, a surface that was never opened up, and a maintenance crew using wax. Each is preventable. We do the first two, and the written procedure covers the third. Call (832) 253-3211 for a free assessment.
Do you handle the whole ESD static control flooring job in-house in Sugar Land?
We do. Prep, base, ground path, topcoat and testing are one package, so there is nobody to hand blame to. On a static floor, two trades working separately is how the layers end up mismatched. Call (832) 253-3211 for your Sugar Land job.
Is ESD flooring worth it for a Sugar Land facility?
It is worth it where the rest of the program depends on it. Wrist straps and footwear only work if they have something to connect to, and that is the floor. For a Sugar Land lab or line with real product at stake, it is usually one of the cheaper controls. Call (832) 253-3211 for an assessment.
How soon can you start ESD static control flooring in Sugar Land?
Book the walkthrough first; that is where timing is set. We test moisture vapor emission (ASTM F1869) and internal relative humidity (ASTM F2170), and once we have those we can schedule. Call (832) 253-3211 for the next open Sugar Land date.
Do you take small ESD static control flooring jobs in Sugar Land?
Small rooms are welcome. The prep and testing do not shrink with the floor, but we will keep the crew and schedule in proportion to the Sugar Land space. Call (832) 253-3211 for a free quote.
Can ESD static control flooring be installed in humid or cold weather in Sugar Land?
The calendar does not matter; conditions do. If the slab is above the dew point and in range, we install. In Sugar Land, that sometimes means a morning start or climate control. Call (832) 253-3211 and we will plan around the weather.
Do you clean up after ESD static control flooring in Sugar Land?
We do, and we contain it as we go. HEPA grinders, plastic barriers where needed and a final cleanup are standard on every Sugar Land job. Call (832) 253-3211.
What primer and topcoat do you use for ESD static control flooring?
A prepared slab, a primer chosen for its moisture condition, a base build, the grounded conductive layer, then the topcoat. The topcoat is 100 percent solids and low odor. Call (832) 253-3211 and we will list the layers for your Sugar Land floor.
What resistance range does your ESD floor meet?
It depends on which grade you choose, and we install either. Conductive is published at 2.5 x 10^4 to 10^6 ohms. Dissipative covers 10^6 to 1.0 x 10^9. We verify the installed floor before handover and share the readings. Call (832) 253-3211 for a Sugar Land quote.
Does ESD flooring need grounding?
Without grounding, a conductive floor is just a conductive floor. We install the ground connections during the build and verify them at handover, which is what lets the floor meet the 1 x 10^9 ohm system ceiling in S20.20. Call (832) 253-3211.
Which standards does it meet?
S20.20 for the program, S7.1 and D257 for the floor measurement, ASTM E648 for flame spread. We provide the paperwork and the test results so your quality team can file them. Call (832) 253-3211 for your Sugar Land quote.
Is it suitable for electronics and labs?
Yes, that is what it is specified for. Electronics assembly, labs, cleanrooms, data rooms and battery work all call for it. The floor holds body voltage generation at 15 V under ANSI/ESD STM 97.2, and it passes ASTM G21 microbial resistance. Call (832) 253-3211 for a free Sugar Land quote.
Do you test and document the performance?
We do, and the readings are yours to keep. If an auditor asks how the floor was verified, you have the numbers and where they were taken. Call (832) 253-3211 for your Sugar Land space.
More New Era floors in Sugar Land
Every system we install in Sugar Land, Texas:
ESD Flooring in other Texas cities
Get your ESD floor specified in Sugar Land
Free on-site assessment. Tell us which room in your Sugar Land building needs static control and what your spec says, and we will put the system and the pricing in writing.
